The plate legend and standards¶
The plate legend says what is in every well. Mplex uses it for one essential thing - finding the standard wells and their concentrations - and it also names wells in exports.
The legend editor is docked on the Legend tab. The plate-legend button on the toolbar opens it in its own window, which has a Close button.
Wells and fields¶
Click a well to edit it; the well name is shown above the fields. Each well has up to four short fields and a free-text note:
| Field | Typical content |
|---|---|
| First field | The sample name - or, for a standard, c and the dilution step |
| Second and third fields | Treatment, donor, time point or any other variable. The label reads Time Point or any variable parameter ( 1,2,3 ...) |
| Fourth field | Copy, replica or duplicate letter (a, b, c ...) |
| Note | Any comment |
The <> buttons between fields swap the contents of neighbouring fields in every well.
Selecting wells¶
| Action | Result |
|---|---|
| Click | Select one well |
| Drag | Select a rectangle of wells |
| Shift +click | Add a well to, or remove it from, the selection |
The stamp¶
The stamp copies wells:
- Select a well, or a block of wells.
- Press the stamp button. The pointer changes.
- Click wherever the copy should go. Repeat as often as needed.
- Right-click to put the stamp back.
Undo and Redo step through your changes; Clear empties the legend; Reset returns to the legend stored with the plate.
Standards¶
A well is a standard when its first field is c followed by a whole number:
| Entry | Meaning |
|---|---|
c0 |
Blank - concentration 0 |
c1 |
The most dilute standard |
c2, c3, ... |
Each one step more concentrated |
cN |
The top standard, where N is the Number of Dilutions |
The concentration of cK for an analyte is
where Cmax is the analyte's top concentration from the assay, F the Dilution Factor and N the Number of Dilutions. Enter both numbers in the boxes of the legend editor. The defaults are 2 and 14.
For example, with a factor of 3 and 7 dilutions, c7 is the top standard, c6 is a third
of it, c1 is 1/729 of it, and c0 is the blank.
Replicate standards simply carry the same entry - put c5 in two wells and both points
are used.
Every well whose first field is not of this form is a sample.
Note
Mplex needs at least five standard wells. With fewer it asks you to mark calibration wells on the plate.
Applying the legend¶
Press Apply to attach the legend to the open plate. It is saved in the plate's INFO
folder and used from then on whenever the plate is opened. Apply replaces the existing
legend without confirmation. Editing the legend highlights Apply in orange until
you apply the changes.
Saving and loading legends¶
Save and Load write and read a legend file. Loading applies the legend immediately. Keep one per plate layout you use
often; Mplex offers %APPDATA%\Mplex\Layouts\ for them. A legend file starts with the
dilution factor and number of dilutions, followed by the plate as rows of comma-separated
entries:
V2
1.5,24
c24,c22,c20,c18,c16,c14,c12,c10,c8,c6,c2,c0
c23,c21,c19,c17,c15,c13,c11,c9,c7,c5,c3,c0
...
Export writes the legend as a readable text file - the plate name, then every well with its fields and note. To CSV writes the plate's results as a table - see Exporting results. Print prints the plate.
The tree and the chart¶
The tree lists the wells grouped by their fields. Tick a branch to select all its wells; the chart then plots the selected wells' results.
NIH export and the viewer¶
NIH exports the plate's results in the folder structure used for NIH data submission:
it asks for a folder and creates primary, derivative and docs in it, each with a
sub-folder named after the Plate Name. Tick Include FCS data to also copy the raw
FCS files into source. The Plate Name must be filled in.
Viewer shows the plate's results in the Mplex Viewer.